There are many ways to DIY burlap fabric flowers. Some easy. Some not so much. The loopy version in this tutorial is super simple to make.
I recently went on a mission to find the technique with the most impact. With no big talent required. I do have a rustic burlap flowers tutorial. But was craving a little more definition.
My rule is to balance the time, talent, and tenacity required for any DIYs I publish. If you are planning a wedding or other event, the last thing you need is to get bogged down in a project!
Plus I am the type who has, ummmm … let’s say rudimentary skills.
On my journey I looked at those burlap roses that look just like the flower. They are so awesome. But time-consuming and tedious for the uninitiated.
An imprecise, freeform method that only looked structured is more my speed. One that is forgiving of mistakes and still looks great.
The Easiest Burlap Flowers to Make
Then I discovered Tiffany Windsor on YouTube. She made some big, amazing blooms as part of a topiary centerpiece.
That had potential.
So I adjusted her method down to a smaller size and tried stacking layers. I added center bling. This was something I could work with. Not hard. Not tedious. Amazing.
I ran with this loopy burlap fabric flower method to create a centerpiece bouquet.
How to DIY this Fabric Flower Centerpiece Bouquet
In the video at the end of this post you can see, step-by-step, how I created the white looped layer. The single layer in the video is only part of how I made this whole look.
Here is an overview of the steps to put the bouquet together …
Note: As with many My Online Wedding Help links, some of the links in this post go to the My Online Wedding Help products section or to a merchant website. That said, THE CHOICES HERE ARE MY OWN. No one paid or asked me to for mention here. If you click and buy a product through one of these links, I will get a small commission at no extra cost to you.
What you Need
- Burlap fabric in two or three colors. I made these with hunter green, white, and natural with gold sparkle.
- Flatback, round pearl and rhinestone decorations for the center.
- 3 green fuzzy chenille craft sticks per flower, for stems (not visible in the above photo).
- Fresh or dried baby’s breath. I bought a bunch with 8 big sprays of fresh baby’s breath from Roberta here.
- Flexible, fabric-friendly glue. Or a glue gun.
- Wire cutters
Steps to Creating the Bouquet
To DIY this centerpiece bouquet:
- First make the blooms, attaching the bottom layer to the stems as you go.
- Then arrange as you like, adding baby’s breath.
- Tie the bunch together with a strip of burlap or twine.
- Cut the stems to the correct length for your vase.
If you use fresh baby’s breath, these instructions are for a short-term bouquet. They should last at least 2-3 days in the fridge, plus normal use the day of the event.
But it’s easy to make the real flowers last longer. To lengthen the life of the baby’s breath, wrap the burlap flower stems in waterproof floral tape to keep them from getting yucky. And add water to your vase.
Bouquet Step 1: Make the Top and Center Looped Layers
Make the top and center layers using the method shown in the looped burlap flowers video at the end of this post. (Or watch How to Make Burlap Flowers with Loops on YouTube then come back here for the rest of the bouquet tutorial). So refer to the video to see how to make these.
I used 3″ white burlap squares and 4″ natural burlap (with gold sparkle) squares.
Bouquet Step 2: Make Stems
Take three chenille stems and twist them, for added strength. You can also use heavy-gauge florist wire and wrap it in florist tape.
Or dowels if you prefer straight, rigid stems. It’s all about the look you are going for.
Bouquet Step 3: Create the Bottom, Green Layer
I pretend this layer is leaves. That’s why I made it green. You can do a different color, or leave the third layer off completely.
That’s the joy of DIY. You can do you.
A. Cut about eight, 5″ squares of hunter green burlap.
B. Pull all but six horizontal (or vertical) strands from the square. Leave three each on opposite sides.
C. Fold and glue into a rectangle, to make loops.
D. Place the stem from step 2 at one end of the glued side of the rectangle. Roll the rectangle around the stem, glueing as you go.
E. Separate and press the loop petals flat against the table. To form a flower shape.
Optionally, spray the flower with fabric stiffener or mod podge. This reduces fuzz. But also makes the loops less pliable to work with later on. Be careful …
Bouquet Step 4: Glue the center and top layers to the stemmed flower.
Dab some glue in the largest- and middle-sized flower layers. And press them together to form a single flower with a stem.
Bouquet Step 5: Add the Embellishment
Place a dot of glue in the center of your top layer. Then place a round, flatback decoration.
Arrange the Flowers
After creating enough flowers to make the size bouquet you want, it’s time to form the arrangement.
I think the bigger one in the mason jar had nine flowers. The one in the cup has three.
Step 6: Form the Bouquet
I in no way resemble an expert florist. Think opposite of that. Which is why I never try to do more than two types of things in one bouquet.
If you do know what you are doing, go wild in this step. It will look better than mine. I promise.
And please post a photo in the comments!
Starting with one or three flowers for the center, hold them by the stems in one hand. Then add sprays of baby’s breath. Alternate baby’s breath and more fabric flowers until you love it.
The beauty of both baby’s breath and burlap flowers is they are meant to be a bit messy. And rustic looking. Both great traits if you lack precision.
Step 7: Tie the stems together at the base of the flowers.
You can also wrap the whole “handle” part of the bouquet in a strip of fabric or ribbon.
Step 8: Tidy the Stems
You may want to manicure the stems. Especially if your vase is clear.
Using wire cutters or pliers, snip the ends of the fuzzy sticks to a uniform length. Straighten or arrange them as you like.
Burlap Loop Flower Video Tutorial
Flower Leaf Pattern
At 8:05 in the video below I show a bottom layer I used as an option for leaves. Instead of the green looped fabric one in the flowers in this blog post.
Here is that flower / leaf template. You can use it to make flowers (but don’t sell it).
If you have a website or social channel, feel free to share the template through them. But please do not remove my information from the file.